Quality Testing Services, Inc.
2305 Millpark Drive,
Maryland Heights, MO 63043
(888) 770-0607
(314) 770-0607
FAX:
(314) 770-0103
Calibration
If there is something not on this list that you would like calibrated, please ask, we may already do it or would like to start. Ask us about coming to your facility to perform the calibrations.
| Aircraft Scales | |
| Alarm Rate Meter | |
| Angle Gage Block Set | |
| Auto Collimator | |
| Bevel Gage | |
| Bond Tester | |
| Bore Gage | |
| Balances/scales | |
| Cable tensiometer | |
| *Calipers (0" - 40") | |
| Chart Recorder | |
| Clamp Meter | |
| Comparator Stand | |
| Contour Probe | |
| Conductivity Meter / Standards | |
| Controllers | |
| Countersink Ring Gage | |
| Countersink Ring | |
| *Current Shunt | |
| *Cylindrical Plug and Pin Gages | |
| Data Logger | |
| Depth Gage | |
| Densitometer | |
| *Dial Indicator (0.00005 to 2) in. | |
| Digital Indicator | |
| Dosimeter | |
| Eddy Current Reference Standard | |
| Eddy Current Unit | |
| Feeler Gage 8 Blade | |
| Field Indicator | |
| Film Viewer | |
| Finishing Depth Block | |
| Flatness | |
| Fluke Thermometer | |
| Force Gage | |
| Gauss Meter | |
| *Gage Blocks (0.05"-20") | |
| *Granite Surface Plates | |
| Flatness 12 inch or greater | |
| Repeatability | |
| Ground Bond Tester | |
| Hand Pull Tester | |
| Hardness Tester | |
| Heat Source | |
| Height Gages (0" - 40") | |
| Hi Potter | |
| Hydrometer | |
| Level | |
| Light Meter (Radiometer) | |
| Ultraviolet | |
| White | |
| Combination White/Ultraviolet | |
| Load Cell | |
| Load Cell 1,000 - 250,000 | |
| Magnetic Particle Equipment | |
| Articulating Probe | |
| Field Indicator (residual magnetism) | |
| Hall Effect Probe Gauss Meter | |
| Mobile Unit | |
| Portable Unit | |
| Shot Duration Meter | |
| Stationary Unit (includes demagnetizing unit) | |
| *Stationary Unit (Amperage and Time) | |
| Material Thickness Gage | |
| *Micrometer (OPD, ID) (0" -24") | |
| Micrometer (OD, ID) (0" - 120") | |
| Mic Master Kit | |
| Micrometer Stand | |
| Micrometer Standards | |
| Meg Ohm Meter | |
| Multimeters | |
| *Optical Comparator | |
| Ovens | |
| Oxygen Gauge (up to 10,000 psi) | |
| Panel Meter Analog or Digital (Stimulate only) | |
| DC Voltage | |
| AC Voltage | |
| DC Current | |
| AC Current | |
| Parallels | |
| Penetrant Test Panels | |
| pH Meter | |
| Plain Cylindrical Plugs (xyz) (.001-10.000" dia) | |
| *Plain Cylindrical Ring Gauges (0.125 to 4 in) | |
| Portable Hardness Tester | |
| *Power Supply | |
| Pecision Ball Set | |
| Precision Weighing Scales (1 mg to 1g) (1 to 600g) | |
| *Pressure Gage (0-10,000 max psi) | |
| Pressure Gage (0-10,000 max psi and 30 InHG max vacuum) | |
| Pressure Transducer | |
| Profilometer | |
| Profilometer Roughness Standard | |
| Propeller Protractor | |
| Protractor | |
| Push Rod | |
| Pyrometer | |
| Radius Gage | |
| Refractometer | |
| Relatie Humidity | |
| Relief Valves | |
| *Resistance Standard | |
| *Rockwell and Rockwell Superficial Hardness Testers | |
| Scales (Rule) (12" - 72") | |
| Scopes | |
| Screw Pitch Gage | |
| Sine Bar | |
| Skewing Height Block | |
| Skidmore | |
| Snap Gage | |
| Special Fixtures | |
| Spring Scale | |
| Square | |
| Steel Square | |
| Step Gages | |
| Step Plug/Ring | |
| Stop Watch | |
| Straight Edge | |
| Surface Finish Gage | |
| Surface Plates | |
| Resurfacing | |
| Survey Meter (X-ray only) | |
| Tachometer | |
| Tam Panels | |
| Taper Gage | |
| Tape Measure | |
| Tape Measure 100' | |
| Temperature Controller | |
| Temperature Mapping | |
| Temperature Probe | |
| Tensiometer | |
| Thermometer | |
| Thermisters | |
| Thermocouple Calibrator | |
| Thermocouple Wire | |
| Thickness / Corrosion Tester | |
| Thickness (Film) Standard | |
| Thickness Standard | |
| *Thread Plugs Features | |
| (Major Diameter and Pitch Diameter) (up to 10 in.) | |
| Thread Plugs (Working) (Setting) (Go/No Go) up to 10 in.) | |
| *Adjustable Thread Ring Gage (up to 1 in.) | |
| Thread Wires | |
| Torque Analyzer | |
| *Torque Wrench (60 to 600 ft. lbs.) | |
| Ultrasonic Blocks | |
| DSC UT Blocks | |
| Type I, IIW UT Blocks | |
| Type II, IIW UT Blocks | |
| 7075-T6AL Distance Amplitude (Quartz Transducer) | |
| Distance Amplitude (Any other Material) | |
| Ultrasonic Flaw Detector (single channel) | |
| Vacuum Gage | |
| Viscosity | |
| Weight Sets | |
| Weight Scale | |
| X-ray Densitometer | |
All information on these pages - © Copyright 2000-, Quality Testing Services, Inc.